Designfax weekly eMagazine

Subscribe Today!

Archives

View Archives

Partners

Manufacturing Center
Product Spotlight

Modern Applications News
Metalworking Ideas For
Today's Job Shops

Tooling and Production
Strategies for large
metalworking plants

Coming soon: Top-shelf dental crowns could be 3D printed at your dentist's office for same-day service

University of Texas at Dallas researchers have developed a technology that enables same-day, 3D-printed dental restorations made of zirconia, the gold-standard material for permanent dental work.

The team is working to make the technology, which could be used for crowns, bridges, veneers, and other restorations, commercially available with support from the National Science Foundation (NSF).

A finished dental crown created by the UT Dallas researchers' technology. [Credit: Image courtesy of UT Dallas]

 

 

"We are excited to be advancing the commercialization of chair-side 3D-printed, all-ceramic zirconia permanent dental restorations," said Dr. Majid Minary, professor of mechanical engineering in the Erik Jonsson School of Engineering and Computer Science. "Because the crowns can be custom printed for each patient on the same day, this approach offers greater personalization, faster treatment, and the convenience of receiving a permanent restoration in a single visit."

Dental crowns are caps that are placed over damaged or decaying teeth. They also can serve as supports in a dental bridge, which replaces a missing tooth. 3D-printed restorations have emerged as an option that offers better customization and color matching, as well as a more efficient manufacturing process that could reduce cost and waste. Currently available same-day, 3D-printed crowns, however, are made of ceramic resins that are not as strong as zirconia.

While same-day zirconia crowns are also available, they are not 3D printed; rather, they are milled, a process that involves carving the crown from a block of zirconia. These zirconia restorations face challenges and limitations in design complexity and risks for micro-cracking during milling or sintering.

The UT Dallas researchers and their collaborators have solved a challenge in producing 3D-printed zirconia restorations by significantly reducing the time involved in processing a zirconia restoration after it is 3D printed. The researchers explain their approach in the September print edition of the journal Ceramics International. The method will require clinical validation and regulatory approval before it becomes commercially available.

After a zirconia crown is 3D printed, it must undergo two key steps: debinding and sintering. In the debinding stage, heat is applied gradually to burn off the resin that held the zirconia particles in place during printing. This process can take from 20 to 100 hours. Once the resin is removed, the crown undergoes sintering -- a high-temperature firing process similar to baking clay in a kiln -- that fuses the zirconia particles together into a dense, hardened solid.

"Debinding has been the bottleneck in the process," said Minary, corresponding author of the article. "It must be done very slowly. If you speed it up, the polymer being burned off turns into gas, and if that gas cannot escape, the crown may crack or fracture. A debinding time of 20 to 100 hours is not practical for same-day dental service. As a result, 3D-printed permanent zirconia restorations are not yet commercially available."

VIDEO: New technology for 3D-printed dental restorations. After a new dental crown is 3D printed, it must undergo debinding and sintering. A new method developed by University of Texas at Dallas researchers combines enhanced heat transfer with the use of porous graphite felt, which can reach temperatures above 2,550 F. [Credit: UT Dallas]

The team's technology reduces debinding time to less than 30 minutes -- a breakthrough that could make same-day, permanent dental restorations possible. Their approach combines enhanced heat transfer with the use of porous graphite felt, which can reach temperatures above 2,550 deg F. The felt covers the 3D-printed restoration, allowing gas released from the resin to escape, while a vacuum system simultaneously removes the gas.

"The combination of all of these features is what makes it work," Minary said. "With our technology, if a practitioner wants to offer a 3D-printed zirconia crown chair-side, they could provide it to a patient within just a few hours."

The UT Dallas team, led by Minary, in collaboration with Pan-AM Dental Laboratory, recently received a $550,000 award through the NSF's Partnerships for Innovation - Technology Translation project to support commercialization of the technology.

The commercialization project also involves 3DCeram Sinto Inc. in Grand Ledge, MI; and Dr. Amirali Zandinejad, a prosthodontist in Arlington, TX, and former associate professor at the Texas A&M University College of Dentistry.

In addition to the NSF, the research in the paper was also supported by the U.S. Air Force Office of Scientific Research.

Source: University of Texas at Dallas

Designfax reader response
My father is a dentist who has been researching crowns for years, since I was a kid. I'm an engineer, and he basically is, too. I have often discussed it with him. Actually, research shows that Zirconia is definitely not the "gold-standard" when it comes to crowns. Gold is still the "gold-standard." Hand-made porcelain fused to metal (PFM) is second. Zirconia is easy to work with (initially) and cheap, which is why it is popular with dentists. But few last long and they usually fit poorly (which can lead to further decay). Even Clinician's Report (sometimes considered the leading dental research org) has had to admit this. Also, Zirconia crowns usually need to be replaced every few years, unlike gold or PFM. To make matters worse, the only way you could 3D print a crown is to do an intraoral 3D scan, a technology that is notoriously unready for mainstream. -- R.T.

Published October 2025

Rate this article